Components NEEDED
Two '/*" x Γ 18-gauge sterling silver sheet silver Two seven/«" sterling silver bar factors Two 5.three mm x three.2 mm 16-gauge sterling silver oval jump rings Two sterling silver ear wires
TOOLS NEEDED
Ruler
Marker
Jeweler's observed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
High-quality grit sanding pad Awl
Tricky, flat floor /Îί’ drill bit
Handheld rotary tool, flex shaft, or drill push Liver of sulfur or oxidizing Resolution Fantastic metal wool Sharpening cloth
Two pairs of chain nose pliers
one.Make use of the ruler to measure and mark two
rectangle parts of 18-gauge sterling sheet silver.
two.Utilizing a jeweler's saw or tin snips, Slice the 18-gauge sterling sheet silver into two Vi" x Γ rectangles (if you may be earning the bracelet and pendant initiatives, you may want to Slice each of the rectangle silver parts required for the opposite tasks and texture all of them at 1 time).
three.Place the two W x Γ sterling silver rectangle parts on to the sticky side of the bit of masking tape. This will allow you to to hold the silver rectangles in position if you are texturing them, and may also support to keep the fingertips at a secure length to prevent hitting them Along with the hammer.
four.Location the piece of masking tape Together with the silver rectangles sticky aspect down on to a concrete block or landscape paver.
five.That has a hammer, Carefully strike the tape-included silver rectangles employing a firm strike, but Never hit way too really hard. You could achieve the specified texture extra conveniently with various tender strikes rather than a couple of hard strikes. Carry the tape routinely and Test the progress from the texturing, ensuring that that your complete area with the silver rectangles is getting a uniform texture. The surface area will look just like sandpaper Should you be using a concrete block. After you obtain the desired texture, clear away the silver rectangles from your masking tape.
six.the silver rectangles can have a slight curve to them, and the perimeters will probably be misshapen and sharp Once you texture them. You are able to depart the silver rectangles curved or, to flatten them, place the silver rectangles on a hard, flat floor and use a rawhide mallet to flatten them. If you do not Use a rawhide mallet, you are able to position the silver rectangles men's designer rings & wedding bands on a hard, flat surface area, protect the parts having a thick piece of scrap leather, and make use of a hammer to Carefully faucet the leather-based covered silver rectangles to flatten them.
7.You have got to utilize a file to reduce any rough or sharp edges. Use a good grit sanding pad to go above the realm where you have filed to easy the edges and remove any file marks.
8.Measure from 1 stop of each textured silver rectangle and location a mark in the center of each piece. This is when the holes are going to be drilled to connect the soar ring and bar elements.
9.Placed on the security Eyeglasses. Area the textured silver rectangles onto a tough, flat area. Area the point from the awl on the mark that you choose to designed '/t" through the stop from the rectangle parts and make use of a hammer to firmly strike when on the top with the awl to produce rings for men a pilot hole for drilling the holes in the silver rectangles.
10.Utilizing a drill bit, drill holes into Just about every from the silver rectangles which has a handheld rotary Device, flex shaft, or drill push. Remember to wear security Eyeglasses.
11.Make use of the file or sanding pad to eliminate any burs or rough edges remaining from drilling holes into the silver rectangles.
12.Utilize liver of sulfur or oxidizing Remedy to your textured silver rectangles, bar components. and leap rings. It men's designer rings & wedding bands is vital to adhere to any security tips the company suggests when working with any chemical substances.
13.Immediately after implementing the oxidizing solution, use good steel wool to get rid of the darkened regions to the lifted floor of the silver rectangles, leaving a few of the textured places men's rings personalized and engraved dark. Rub the fantastic steel wool more than the jump rings and bar components to eliminate some although not most of the darkened parts. Rinse with drinking water, dry, and rub with sharpening cloth.
fourteen.With two set of chain nose pliers pointing up, hold the jump ring With all mens casual rings the opening at the top. Roll one within your wrists faraway from you and your other wrist toward you, opening the soar ring only up to required. To shut the soar ring, hold it a similar way and roll your wrists in the other direction (visualize holding a bit of paper and tearing it). Never ever pull the jump ring finishes out as this will likely weaken the metal, and it will be difficult to near the bounce ring.
15.Increase the bar element and textured silver rectangle to your jump ring. Near the bounce ring.
16.Carefully open up the loop at the bottom on the ear wire, increase another conclusion of the bar component. after which shut the ear wire loop.
17.Repeat these techniques for the 2nd earring.